Memory FAQs
 
Home
News
Products
Shop
Memory
Corporate
Contact
 

News
Industry News
Publications
CST News
Help/Support
Member Area
Tester Brochure
Demo Library
Software
Tester FAQs

biology medicine news product technology definition

Monday, October 16, 2017
Memory Articles and Publications
Email ArticlePrinter Format PreviousNext

How to Fix DIMM Memory - Part 4 ( Final Chapter)


Friday, October 09, 2009

How to Fix DIMM Memory - Part 4  ( Final Chapter)
 
In this Part-4 of the troubleshooting memory-guide, we discussed about the basic technique on how to replace a defective memory chip and rework a defective memory module.

Read Part-3 if you have missed the previous article on How to Test for Defective Memory.

http://www.simmtester.com/page/news/showpubnews.asp?title=How+to+Fix+Memory+%2D+Part+3++%28+revised+version+2009+October%29&num=170 



How to add/replace a DRAM memory chip from a DIMM Memory ?
 
Warning
If your soldering skill is not good enough or if you don't feel confident - please do not proceed with this project. The Soldering iron are very hot ! Don't get burn by the soldering irons !

example of TSOP IC soldering

Let's begin

First, note that the pictures in this how-to were taken while adding a memory chip; if you want to replace the main defective chip just follow the this instructions and you will most likely be able to start replacing the faulty chips.
 
In this example , the dram chip is a TSOP package which have gull-wing metal leads and its easy to desolder the chip from the PCB board. Adding a new chip to the DIMM PCB board is simple since you only need soldering iron with a fine tip to get the job done.
 
 
Gull-wing lead frames , easy to rework with standard soldering tools.
 
However, for reworking BGA chips, it will require specialized rework equipments to remove the BGA device and to replace the components. BGA rework is alot harder than surface mount TSOP devices. See illustration of a DIMM using BGA device, soldering leads are not accessible.
 
 
(Side-View BGA device connection leads are under the device,not possible to rework with soldering tools)

Here are the tools needed in this project:
 

 
In this project, the target chip is a 512 MB DDR DIMM memory, using 64Mx8 (66 pin TSOP) memory chips ( Infineon ) DDR chip.

How to get a new working chip ?

You can get an extra memory chip from other defective DIMM memory, make sure you marked the good working chips. Most DIMM memory module manufacturers uses the following fixture to test chips before soldering the chips on the PCB board.
 
Notice the TSOP test fixture looks similar to a DIMM module except it has test sockets for inserting chips.
 
Extracting known bad memory chip ( marked X) from the DIMM module. This module have been tested with a CST SP3000 DDR Tester and chip U1 is bad.
 
DDR DIMM - 512Mb ( 64Mx72) Total 9 chips

If you already have a known good memory chip ,it is safe to skip this section and proceed to "Preparing to solder the second chip".
 
Make sure you do not mixed different brands of memory chips on the same DIMM module, otherwise the module will not operate properly.

 
Disassemble the bad chip U1.
 
 
 
Hold down one side of chip and gently apply some heat to desolder it.
 
Attention!
 
Do not over-heat chip with soldering gun/iron. 
  
Here's the 64Mx8 DDR memory chip. Pins will be dirty after removal (tin + rosin).
 
 

Clean it so there are no short circuits. It is now ready to use!
 
- Preparing to solder the second good chip
- Disassemble the faulty chip and secure it to a table, with the free soldering place face up.
- The "o" symbol marks position of first pin of memory chip! This is very important! You can't turn chip around during soldering. The chip MUST be correctly - aligned! Take a look at the pin 1
 

 
- Clean the free soldering place on the circuit board of the with alcohol, if necessary. 
 
Soldering the chip
 
Apply tin to solder the chip legs to the board. This is the most dangerous and difficult part as the pins are so small and close that it is very easy for solder to bridge across the pins.
 
Tips:
Use as little tin as possible. Soldering areas are just covered - it should be enough.

Place the DDR chip very precisely on the soldering pads.
 

 
Solder first and last pin, then check if location of chip is correct. If it's OK, then solder the rest of the pins - side by side.
 
example of good solder joints

STOP and CHECK with multimeter and magnifying glass , MAKE SURE that there are no short-circuits between chip legs. 
 

 
Testing the DIMM module 

For a final test, load the DIMM module on the PC motherboard and test if able to boot-up 
 
 
If everything works fine, If something wrong happens, check for short-circuits on the soldering work you've made.
 
Final result and test on the motherboard.
 
For details on how to use Diagnostic cards for testing memory module,
check out this article on " Memory Test Software Review".
 
 
 

By: DocMemory
Copyright 2009 CST, Inc. All Rights Reserved

Email ArticlePrinter Format PreviousNext
Latest Publication News
Next big thing for DDR4 Memory 3DS DDR4 Devices11/20/2015
Challenges of testing mobile memories1/15/2014
Understanding DDR4 Serial Presence Detect (SPD) Table11/25/2013
What is Hybrid DIMM Memory Module ?3/19/2013
What is DDR4 Memory ?3/18/2013
New Memory Module Picture 20131/21/2013
Challenges of testing mobile memories2/8/2012
What is LPDDR Memory ?7/20/2011
Determine Endurance on a NAND Flash Chip4/5/2010
Smartphone Memory and Test Challenges4/5/2010

CST Inc. Memory Tester DDR Tester
Copyright © 1994 - 2017 CST, Inc. All Rights Reserved