DocMemory
 
Home
News
Products
Shop
Memory
Corporate
Contact
 

News
Industry News
Publications
CST News
Help/Support
Member Area
Tester Brochure
Demo Library
Software
Tester FAQs

biology medicine news product technology definition

Tuesday, September 30, 2014
Memory Articles and Publications
Email ArticlePrinter Format PreviousNext

Common DIMM Memory Form Factors


Tuesday, October 06, 2009

This technical note provides a comparison of the most common DIMM memory module form factors. All the module form factors discussed in this technical note all modules are manufactured by various manufacturers.

The easiest way to categorize memory module is by form factor. The form factor of any memory module describes its size and pin configuration. Most PC systems have memory sockets ( slots) which can accept only one type of form factor. Some computer systems are designed with more than one type of memory socket, allowing a choice between two or more form factors.

Mechanical Outlines FAQ

JEDEC specifies mechanical outlines (MOs) to provide an industry standard that can be used by any module manufacturer. These specifications can be accessed on the JEDEC Web site and are referenced by numbers.

http://www.jedec.org/

For example, the MO for DDR3 standard- length modules is MO-269.

Typical mechanical specification

MOs are referenced throughout this technical note and are organized by size. Dimensions provided represent only one variation of the JEDEC standard and are intended for general reference; they are not meant to be substitutes for the dimensions in JEDEC MOs.

Most memory module dimensions have recently been converted from inches to millemeters as a standard. In this article, all units of measures will be in millimeters instead of inches.

Some Common Memory Module PCB Physical Sizes

DIMM Dimensions are Length x Height x Width
DIMM = Dual In-Line Memory Module

FBDIMM [133.35mm x 30mm x 5.1mm L x H x W]
FBDIMM = Fully Buffered DIMM
No of Pins - 240-pin DIMM DDR2 Modules

Mini-DIMM [ 82mm x 30mm x 3.8mm L x H x W]
Mini-Dual In-Line Memory Module
No of Pins =244-pin DIMM DDR2 Modules

Mini-RDIMM [82mm x 30mm x 3.8mm L x H x W]
mini Registered DIMM
No of Pins =244-pin DIMM DDR2 Modules

RDIMM [133.35mm x 30mm x 4mm L x H x W]
Registered DIMM
No of Pins =240-pin DIMM DDR2 Modules

SODIMM [67.6mm x 30mm x 3.8mm L x H x W]
Small Outline DIMM
No of Pins = 200-pin DIMM DDR2 Modules

SOCDIMM [67.6mm x 30mm x 3.8mm L x H x W]
Small Outline Clocked DIMM
No of Pins = 200-pin DIMM DDR2 Modules

SORDIMM [67.6mm x 30mm x 3.8mm L x H x W]
Small-Outline Registered DIMMs
No of Pins  200-pin DIMM DDR2 Modules

UDIMM [133.35mm x 30mm x 4.0mm L x H x W]
Unbuffered DIMM
No of Pins  240-pin DIMM DDR2 Modules

VLP Mini-RDIMM [82.1mm x 18mm x 3.8mm L x H x W]
Very Low Profile memory Mini-RDIMM
No of Pins = 244-pin DIMM DDR2 Modules

VLP-RDIMM [133.35mm x 18mm x 4.0mm L x H x W]
Very Low Profile memory-RDIMM
No of Pins =240-pin DIMM DDR2 Modules

VLP SORDIMM [67.6mm x 18mm x 3.8mm L x H x W]
Very Low Profile Small-Outline Registered DIMM
No of Pins =200-pin DIMM DDR2 Modules

Common Standard-Length Modules

The standard-length module is the most commonly used module form factor. With a typical length of 133.35mm, these DIMM memory modules will accommodate the highest number of DRAM components.

Most standard-length modules are 30mm high and used in various applications where real estate is not an issue. Desktop, servers, and workstations are not usually constrained by vertical height restrictions and thus, the 30mm height is easy to accommodate without restricting other mechanical obstructions.

To prevent DIMM modules from being installed in the non- supported systems, the voltage alignment key notch is used in different location for each technology to differentiate the various type of memory technology. 

Standard DIMM Form Factors.

DDR3 - 240 pin Unbuffered / Registered DIMM

DDR2 - 240 pin Unbuffered / Registered DIMM

DDR2 - 240 pin VLP DIMM

 DDR2 244pin Mini Registered DIMM

DDR - 184 pin Unbuffered / Registered DIMM

SDRAM - 168pin Unbuffered / Registered DIMM

Standard SODIMM Form Factors.

SODIMMs were designed to fit into notebook PCs and other small systems. Note that theSODIMMís size can restrict the maximum density of the module compared to full-lengthmodules.

DDR3 204pin SODIMM

DDR2 200pin SODIMM

DDR 200pin SODIMM

SDRAM 144pin SODIMM

 

In conclusion , Jedec will continue to define and approved various new form factors and its unlikely the memory form factors will continue to increase or decrease in size. Based on the last few memory technology migrations, the standard DIMM length of 133.35 mm will continue to stay for a long period, meanwhile the form factors for SODIMM length will remain at 67.6mm. One thing for sure , the number of pin counts  may increased however the dimension of the memory module form factor will remain unchanged.

 

By: DocMemory
Copyright © 2009 CST, Inc. All Rights Reserved

Email ArticlePrinter Format PreviousNext
Latest Publication News
Challenges of testing mobile memories1/15/2014
Understanding DDR4 Serial Presence Detect (SPD) Table11/25/2013
What is Hybrid DIMM Memory Module ?3/19/2013
What is DDR4 Memory ?3/18/2013
New Memory Module Picture 20131/21/2013
Challenges of testing mobile memories2/8/2012
What is LPDDR Memory ?7/20/2011
Determine Endurance on a NAND Flash Chip4/5/2010
Smartphone Memory and Test Challenges4/5/2010
New DIMM Memory Tester Revolutionized DDR3 Testing1/5/2010

CST Inc. Memory Tester DDR Tester
Copyright © 1994 - 2014 CST, Inc. All Rights Reserved